API 5L HFW Pipes PSL 1 & PSL 2 — Non Sour Service

About this product

API 5L WELDED PIPE PRODUCTION Jazeera Steel has a world class API-5L welded pipe production facility. API -5L Process Flow Chart TECHNICAL DATA OF BLACK & BARE STEEL HFW PIPES CONFORMING TO API 5L STEEL G RADE UPTO X52 PSL 1 & PSL 2 Manufacturing of HFW Black Tubes and Pipes as per API Spec Q1: 2023 10th Edition and API 5L specification; Steel Grade up to X52 PSL-1 and Steel Grade up to X52M PSL-2, X 52 MS PSL-2, X 52 MO PSL-2 and the product is intended for use in the petroleum and natural gas industry. Nominal Pipe Size: 88.9 to 219.1 MM OD Wall thickness from 3.18 mm Minimum to 8.18 mm Maximum. Length range is 6.00 to 13.5 meters. SIZING DETAIL MANUFACTURE IN OUR FACILITY Chemical Property: a Cu ≤ 0.50 %; Ni ≤ 0.50 %; Cr ≤ 0.50 % and Mo ≤ 0.15 %. b For each reduction of 0.01 % below the specified maximum concentration for carbon, an increase of 0.05 % above the specified maximum concentration for Mn is permissible, up to a maximum of 1.65 % for grades ≥ L245 or B, but ≤ L360 or X52; up to a maximum of 1.75 % for grades > L360 or X52, but < L485 or X70; and up to a maximum of 2.00 % for Grade L485 or X70. C Unless otherwise agreed, Nb + V ≤ 0.06 %. d Nb + V + Ti ≤ 0.15 %. e Unless otherwise agreed. f Unless otherwise agreed, Nb + V + Ti ≤ 0.15 %. e Unless otherwise agreed, Cu ≤ 0.50 %; Ni ≤ 0.30 %; Cr ≤ 0.30% and Mo ≤0.15%. d Nb + V + Ti ≤ 0.15%. Mechanical Property: Af = C^xc Ư0.9 0.2 where is 1940 for calculations using SI units and 625,000 for calculations using USC units; C Axc is the applicable tensile test piece cross-sectional area, expressed in square millimeters (square inches) as follows: 1) for circular cross-section test pieces, 130 mm2 (0.20 in.2) for 12.7 mm (0.500 in.) and 8.9 mm (0.350 in.) diameter test pieces, and 65 mm2 (0.10 in.2) for 6.4 mm (0.250 in.) diameter test pieces; 2) for full-section test pieces, the lesser of a) 485 mm2 (0.75 in.2) and b) the cross-sectional area of the test piece, derived using the specified outside diameter and the specified wall thickness of the pipe, rounded to the nearest 10 mm2 (0.01 in.2); 3) for strip test pieces, the lesser of a) 485 mm2 (0.75 in.2) and b) the cross-sectional area of the test piece, derived using the specified width of the test piece and the specified wall thickness of the pipe, rounded to the nearest 10 mm2 (0.01 in.2); U is the specified minimum tensile strength, expressed in megapascals (pounds per square inch). CVN absorbed energy requirement for pipe body of PSL 2 pipe Seam Normalizing: Seam normalizing is performed to improve the microstructure and mechanical properties of the weld zone, ensuring uniformity and reducing the risk of corrosion. Non-destructive Testing: Additionally, non-destructive tests such as eddy current, ultrasonic testing, magnetic particle inspection, and visual inspection are performed as per API 5L Annexure E to verify pipe Quality. Marking: After the pipe meets all testing requirements, it is marked with the following information AL JAZEERA STEEL PRODUCTS CO. SAOG API SPEC. 5L-1299 [MONOGRAM] (MM-YR) OD WT MM GRADE HFW PIPE NO - - - - HYDRO TEST PRESSURE ------ MPa HEAT NO L ------ M WEIGHT